TaheriFix
Practical guide

IKEA PAX Wardrobe Assembly in Montreal: Measure, Anchor and Plan First

Plan an IKEA PAX wardrobe around ceiling clearance, baseboards, wall anchoring, doors and condo or rental requirements before assembly day.

· 8 min read

Updated:

All guides →

Confirm the exact PAX combination before opening boxes

PAX is a system rather than one standard cabinet. Frame height, width and depth, hinged or sliding doors, corner units and KOMPLEMENT interiors all change the assembly sequence and the space required. Start with the final IKEA planner list, product numbers and current instructions for every frame, door and interior accessory. Check that the delivered packages match the plan before removing all packaging or mixing fittings between boxes.

Measure the intended wall at several points because Montreal apartments and older homes can have uneven floors, sloped ceilings and walls that are not perfectly square. Record floor-to-ceiling height, wall width, available depth, door swing, outlets, switches, radiators, vents and nearby room doors. Also measure the narrowest elevator, corridor and doorway used to bring the packages to the room.

Leave enough ceiling clearance for the chosen assembly method

Ceiling height is not just the frame height. IKEA publishes minimum clearances that vary by frame and door type, and the current product instructions control. A frame assembled flat needs room to be raised without striking the ceiling; an upright assembly may use a different sequence and minimum clearance. Sliding-door hardware can require more space above the frame than a doorless or hinged-door solution.

Measure after accounting for rugs, flooring transitions, ceiling bulkheads and any planned levelling. Do not assume that a nominal eight-foot ceiling is uniformly eight feet across the wall. If clearance is close, confirm the exact frame model and instruction version before scheduling. Forcing a tall frame upright can damage the ceiling, frame corners or connectors and may leave no workable space for final adjustment.

Plan around baseboards, floors and imperfect walls

A baseboard can hold the wardrobe away from the wall and change the reach of the supplied attachment brackets. Decide whether the approved plan is to keep the baseboard, create an appropriate spacer or have trim modified separately. Never cut building trim, move a radiator or alter a wall simply to make the cabinet fit without the property owner's permission and a clear scope.

The floor must support the wardrobe evenly. Identify loose flooring, pronounced slopes, damaged trim and moisture before assembly. Small manufacturer-permitted adjustments are different from trying to make the cabinet compensate for a seriously uneven floor or unsound wall. Protect finished floors during sorting and assembly, keep hardware in labelled groups and reserve a clean area large enough for panels to lie flat without being stepped on.

Treat wall anchoring as required safety work

IKEA warns that PAX must be secured to the wall to reduce the risk of tip-over. The attachment device may be supplied, but screws and plugs for the building wall are selected separately because drywall, plaster, wood framing, concrete and masonry need different fasteners. The visible wall finish does not always reveal what is behind it, so wall type and sound attachment points must be confirmed.

Before drilling, check for electrical wiring, plumbing and other hidden services. Do not use an anchor based only on cabinet weight or a generic online chart; consider the manufacturer's attachment detail, wall construction, fastener approval and actual conditions. If the wall is damaged, wet, crumbling, unusually built or cannot provide a reliable attachment, stop and refer the repair or assessment to the appropriate qualified professional.

Sequence frames, doors and interiors carefully

Multiple frames should be levelled, aligned and connected in the order shown by the instructions before loading shelves, drawers and clothing. A small error at the first frame can appear later as uneven gaps, drawers that rub or doors that do not meet. Hinged doors need clear swing space; sliding doors require their own rail, panel and clearance sequence. Corner combinations must begin with the component specified by IKEA.

Keep the complete hardware set until final adjustment is finished. Test every door, drawer, pull-out tray and clothes rail without overloading it. Confirm that the wardrobe is stable, attached, level and clear of outlets, vents and heat sources. Packaging should be removed only after parts and finishes have been checked, since a damaged panel or missing fitting may need to be identified by its product package.

Prepare the room and permissions before the appointment

Clear the room, remove fragile objects and provide safe working access to the full wall. Send the IKEA planner link or item list, frame dimensions, door type, room measurements and photos showing the wall from corner to corner, floor, ceiling, baseboard and nearby obstacles. State the number of packages, their location in the building and whether elevator booking, loading access or parking restrictions apply.

For a rental or condo, confirm rules for drilling, noise, delivery and common-area protection before work begins. TaheriFix can review ordinary furniture assembly, alignment and attachment needs and then have a person confirm scope and price. Wall repair, uncertain hidden services, structural changes, fixed electrical work, plumbing changes, asbestos concerns and major trim alterations are not part of routine PAX assembly and require separate assessment.

FAQ

Frequently asked questions

Can PAX be assembled if the ceiling is only slightly taller than the frame?

Sometimes, but the required clearance depends on the exact frame, door system and approved assembly method. Check the current IKEA instructions and measure the lowest point of the ceiling before booking.

Does an IKEA PAX wardrobe have to be attached to the wall?

Yes. IKEA identifies wall attachment as necessary tip-over protection. Use the supplied attachment device with screws and plugs suitable for the actual wall construction.

Are wall screws and plugs included?

The wall attachment device may be included, but wall screws and plugs are generally selected separately because the correct fastener depends on drywall, plaster, wood, concrete or masonry.

Can the wardrobe sit in front of an existing baseboard?

It may, but the gap changes alignment and anchoring. The baseboard, approved spacer and bracket reach should be planned before assembly rather than improvised after the frames are built.

Should hinged or sliding doors be chosen first?

Choose before installation. Door type affects ceiling clearance, front working space, hardware, assembly sequence and whether nearby furniture or room doors can operate normally.

What should I send for an assembly estimate?

Send the IKEA planner or item list, frame sizes, door type, package count, ceiling and wall measurements, full-room photos, wall type if known and building access details.

Photo Quote

Send photos for a faster estimate

Include your postal code, a short description and clear photos of the work area and product.

Send Photos
TextCallFree EstimateConnect